Did your Messana App show the message “Supply temperature doesn’t reach the target (level 1)” or “Supply temperature doesn’t reach the target (level 2)”? Don’t worry. This message tells you that your heating or cooling system is working harder than usual to get the water to the right temperature. In some cases, it clears on its own. This article explains what the message means, why it happens, and what you can safely check yourself.
What the message means
Your Messana system heats and cools your home by sending water through your radiant panels or fan coils. The water that leaves the mechanical room is called the supply water. For each moment, your system calculates the ideal temperature for that water. This is the target.
The “Supply temperature doesn’t reach the target” message appears when the supply water stays too far from its target for too long. By default, that’s 15 minutes. In other words:
- In heating, the water is colder than it should be.
- In cooling, the water is warmer than it should be.
This usually means your heat pump, boiler, or chiller isn’t delivering enough heating or cooling at the moment.
Warning or alarm: which one do I have?
The message comes in two levels. You can tell them apart by the end of the name:
| Level | Name in the App | How it looks | What it means | What the system does |
|---|---|---|---|---|
| Level 1 (warning) | “Supply temperature doesn’t reach the target (level 1)” | Yellow flag | The water is a little off target. | Nothing changes. Your system keeps running as usual. |
| Level 2 (alarm) | “Supply temperature doesn’t reach the target (level 2)” | Red flag | The water is off target. for a prolonged time. | Depending on your system’s settings, it may pause the affected hydronic circuit to protect it. |
If the level 2 alarm pauses a circuit, the system closes the mixing valve and turns off the pump for that circuit. Then it waits for the water temperature to recover before it starts again.
Why doesn't the supply temperature reach the target?
The most common reasons are:
- The heat pump, boiler, or chiller is off or has a fault. For example, it lost power or its in an error state and not functioning.
- The buffer tank isn’t up to temperature yet. This often happens right after the system starts, or after a long period off.
- There isn’t enough water flow. A pump may not be running due to it being in alarm, it could be off, or there may be air in the pipes.
- The demand is higher than the equipment can deliver. This can happen on very cold or very hot days. although uncommon.
- A temperature sensor is giving a wrong reading. The system then thinks the water is off target when it may not be.
What can I check?
Before you call for help, try these simple checks:
- Wait a little. If the system has just started, or the weather is extreme, give it 30 minutes. A level 1 warning often clears on its own once the equipment catches up.
- Check your heat pump, boiler, or chiller. Is it powered on? Does its display show an error? Also, check that its breaker hasn’t tripped.
- Check the trend in the App. Use the Graphs feature to see if the supply temperature is moving closer to the target or staying flat.
- Note when it happens. For example, does it show up every morning or only on the hottest days? This information helps your installer find the cause quickly.
Important: Please don’t open the mechanical equipment, bleed air from pipes, or change valve positions yourself. These tasks need a qualified hydronic contractor.
Does the alarm go away on its own?
Yes. The message clears automatically once the supply temperature is back close to the target. A level 2 alarm first drops to a level 1 warning as the temperature improves. Then it clears completely when the water reaches the target range. If there is an issue with your system e.g. Heat pump alarm, Pump alarm, etc. Those issues would need to be resolved for the system to work properly and the alarm to clear.
When should I contact my installer?
Please contact your installer if the supply temperature doesn’t reach the target and:
- You see “Supply temperature doesn’t reach the target (level 2)” (red flag).
- “Supply temperature doesn’t reach the target (level 1)” (yellow flag) keeps coming back, or lasts for several hours.
- Your heat pump, boiler, or chiller shows an error.
Your installer is your first point of contact for issues with the mechanical equipment, such as heat pumps, pumps, and valves. When you contact your installer, let them know when the message started and what you’ve already checked.
Still having trouble?
- The name of your system and the affected circuit
- The exact alarm name shown in the App (for example, “Supply temperature doesn’t reach the target (level 2)”)
- When the message started and how often it appears
- A screenshot of the alarm and of the supply temperature graph